Environmental monitoring systems prevent hardware damage to server rooms, data centers and network closets with critical condition alerts and remote reboot capability.
Also known as: remote environment monitoring system, monitor server rooms, data center monitoring, computer room, network closet, temperature sensor, remote power reboot, web alert thermometers, server room monitoring.
Environmental threats in your server room can cause a lot more damage than hardware or software problems. Redundant hardware, backup tapes, UPS battery arrays, generators and other fault-tolerance measures can all be rendered useless if your server room overheats or floods. Don't ignore environmental threats – remotely manage them with our Klasys range of Server Room Environment Monitoring System or Intelligent Power Distribution Control Unit via TCP/IP Ethernet protocol over CAT5 through an RJ45 connector.
Monitor Temperature The most common environmental threat in any server room or wiring closet is heat. Detect critical rises or drops in temperature, and receive notifications when heating problems occur.
Monitor Humidity Detect abnormal humidity conditions. You define the humidity levels that are appropriate for each sensor's environment.
Detect the Presence of Water Whether it's a tripped sprinkler system or a flash flood, a server room or wiring closet is just about the last place you want to see water. Receive notification as soon as water makes an appearance.
Monitor Physical Security Monitor "dry-contact" devices including motion sensors, door sensors, vibration sensors and smoke detectors.
Control Power Remotely reboot and control power (on/off) to servers and network devices.
And many more….
-------------------------------------------------------------------------------------------------------------------------------------------
And many more….
-------------------------------------------------------------------------------------------------------------------------------------------
K-FCS Low-Cost Environment Monitoring System – Supports up to 24 Temperature Sensors
Real-time environment and security monitoring and alerts over IP
Daisy-chain many temperature/humidity/dew point, thermocouple, and digital input sensors
Also known as: Remote environment monitoring system, EMS, monitor networking closets, server room alert, IP temperature humidity sensor, web enabled thermostat thermometer alarm logger.
Real-time environment and security monitoring and alerts over IP
Daisy-chain many temperature/humidity/dew point, thermocouple, and digital input sensors
Also known as: Remote environment monitoring system, EMS, monitor networking closets, server room alert, IP temperature humidity sensor, web enabled thermostat thermometer alarm logger.
PRODUCTS DESCRIPTION
The FCS Environment Monitoring System (EMS) with 1-Wire Sensor Interface monitors critical environmental conditions, such as temperature, humidity, liquid water presence, power, intrusion, and smoke. When a sensor goes out of range of a configurable threshold, the system will notify you via email, web page, network management (SNMP), and/or SMS messages (via external USB 3G modem).
The system supports 24 single reading 1-wire sensors in any combination - temperature, humidity, dew point, thermocouple or digital inputs-and 2 separate digital inputs.
The system supports 24 single reading 1-wire sensors in any combination - temperature, humidity, dew point, thermocouple or digital inputs-and 2 separate digital inputs.
• Monitor and manage environmental and security conditions over IP.
• Sensors supported:
o 2 digital inputs sensitive to contact closure.
o 2 RJ11 6P4C connectors for daisy-chaining 1-wire temperature/humidity/dew point, thermocouple, or digital input expanders in any combination.
• Sensors supported:
o 2 digital inputs sensitive to contact closure.
o 2 RJ11 6P4C connectors for daisy-chaining 1-wire temperature/humidity/dew point, thermocouple, or digital input expanders in any combination.
Up to 24 temperature, thermocouple, or any single reading 1-wire sensor can be connected between both RJ11 connectors.
Up to 8 temperature/humidity/dew point combination 1-wire sensors can be connected between both RJ11 connectors. Each temperature/humidity/dew point sensor is equivalent to 3 single reading sensors.
Up to 12 FCS digital input expanders can be connected between both RJ11 connectors to allow a maximum of 24 additional digital inputs. Each FCS-1W is equivalent to 2 single reading sensors.
Maximum cable length supported on each connector is up to 600ft (183 m) depending on the configuration and number of connected sensors.
Use RJ11 splitters (RJ11-3JCK) to daisy-chain 1-wire sensors (sold separately).
• Sensors are hot pluggable.
o The sensors will automatically be detected on power up or a Detect Devices button on the summary page can be selected when logged into the unit.
• Monitors (ping) up to 4 IP network devices - alerts are sent if devices are not responding.
• Sensor conditions can be configured to trigger alerts by themselves, and/or be used in combination with other alerts to trigger one Smart Alert.
• Supports 4 IP network video cameras for live view of any facility.
• Create multiple alerts for any installed sensor.
• Sensor conditions can be configured to trigger alerts by themselves, and/or be used in combination with other alerts to trigger one Smart Alert.
o Configure up to 32 alerts, and one Smart Alert.
• USB port for connecting USB modem.
• Dual redundant power supplies for connection to two separate power sources.
o The second power supply is sold separately.
• Available with optional Power over Ethernet (POE).
• Integrates with various Open Source SNMP monitoring packages - Nagios and MRTG
o The unit can be polled via SNMP.
• Security: HTTPS, SSLv3, AES 256-bit encryption, 16-character username/password authentication, user account restricted access rights.
• Ideal for a wide range of applications including IT infrastructure monitoring, cold storage/freezer monitoring, or any unmanned area that needs to be monitored.
Up to 8 temperature/humidity/dew point combination 1-wire sensors can be connected between both RJ11 connectors. Each temperature/humidity/dew point sensor is equivalent to 3 single reading sensors.
Up to 12 FCS digital input expanders can be connected between both RJ11 connectors to allow a maximum of 24 additional digital inputs. Each FCS-1W is equivalent to 2 single reading sensors.
Maximum cable length supported on each connector is up to 600ft (183 m) depending on the configuration and number of connected sensors.
Use RJ11 splitters (RJ11-3JCK) to daisy-chain 1-wire sensors (sold separately).
• Sensors are hot pluggable.
o The sensors will automatically be detected on power up or a Detect Devices button on the summary page can be selected when logged into the unit.
• Monitors (ping) up to 4 IP network devices - alerts are sent if devices are not responding.
• Sensor conditions can be configured to trigger alerts by themselves, and/or be used in combination with other alerts to trigger one Smart Alert.
• Supports 4 IP network video cameras for live view of any facility.
• Create multiple alerts for any installed sensor.
• Sensor conditions can be configured to trigger alerts by themselves, and/or be used in combination with other alerts to trigger one Smart Alert.
o Configure up to 32 alerts, and one Smart Alert.
• USB port for connecting USB modem.
• Dual redundant power supplies for connection to two separate power sources.
o The second power supply is sold separately.
• Available with optional Power over Ethernet (POE).
• Integrates with various Open Source SNMP monitoring packages - Nagios and MRTG
o The unit can be polled via SNMP.
• Security: HTTPS, SSLv3, AES 256-bit encryption, 16-character username/password authentication, user account restricted access rights.
• Ideal for a wide range of applications including IT infrastructure monitoring, cold storage/freezer monitoring, or any unmanned area that needs to be monitored.
for more info and deployment in your server room, dial 080'-3836-8255, 080'-599-04321
0 Yorumlar